MEDMIX Dispenser Guns

A major reference in dispensing equipment, MEDMIX offers dispenser guns designed for consistent extrusion, thoughtful ergonomics, and recognised reliability in both workshops and on construction sites.

Covering cartridge formats 1K and 2K, foil packs 300/400/600 ml, and ratios 1:1/2:1/4:1/10:1, the range addresses the essential needs for glues, structural adhesives, and sealants, with a wide choice of static mixers and nozzles.

 

What is a Pro Dispenser Gun?

 

An extrusion gun converts energy (manual force, compressed air, motor) into a controlled flow of adhesive or sealant through a nozzle.

The objective: Bead stability, repeatability, and operator comfort.

The MEDMIX range covers 1K needs (sealant/silicone glue, MS, PU) and 2K needs (adhesives with static mixer) with bodies adapted to formats 50–600 ml and usual ratios (1:1, 2:1, 4:1, 10:1). Coaxial and tandem variants exist for two-component cartridges.

 

Why Choose MEDMIX?

 

Beyond a simple "gun", this equipment delivers regular thrust, features rigid chassis that limit pulsation, and integrates a wide ecosystem of accessories (static mixers, nozzles, adapters).

The result: Fewer bead defects, less operator fatigue, and flow consistency that secures your cycle times in the workshop as well as on-site.

MEDMIX covers the following three dispensing methods:

  • Manual: Precision and rework.
  • Pneumatic: High production rates and high viscosities.
  • Battery-operated: Mobility and consistency without air lines.

For detailed criteria and a complete comparison of drive mechanisms, refer to the article ACROM Dispensing Equipment Range.

 

Product Focus

 

The models below are among the most appreciated for their ergonomics, robustness, and ease of use:

Manual

  • 1K: H40+ (290–310 ml cartridges), PowerFlow Combi (290–310 ml cartridges + 300/400/600 ml foil packs)
  • 2K: MR52-07 (50 ml – ratios 1:1/2:1/4:1/10:1), DM2X (400 ml – 1:1/2:1/4:1/10:1)

Pneumatic

  • 1K: Airflow II Cartridge (290–310 ml cartridges), Airflow II Sachet (300/400/600 ml foil packs)
  • 2K: DP2X (400 ml – 1:1 to 10:1), TS488XM (600 ml – 1:1)

Battery-Operated

  • 1K: Electraflow Plus 310, Electraflow Plus 600 Combi
  • 2K: Electraflow VBE 400 MR (400 ml – 1:1/2:1/4:1 and 490 ml – 10:1)

(The final reference is always validated based on your products and technical data sheets.)

 

Compatibilities: Formats & Ratios

 

Before any selection, format and ratio condition success.

MEDMIX covers industrial consumables and professional maintenance: cartridges 290/300/310 ml (including silicones), foil packs 300/400/600 ml, 2K cartridges 50/200/400/490 ml and 2×310 ml, in 1:1/2:1/4:1/10:1 via tandem or coaxial bodies.

The MIXPAC (Medmix) range guarantees wide availability of static mixers, nozzles, and adapters, useful for supply continuity.

 

Summary Table

 

Criterion

MEDMIX

Mixer/Nozzle Ecosystem

Very wide, MIXPAC standard

Chassis Rigidity/Ergonomics

Very high

2K Formats Covered

50/200/400/490 ml, 2×310 ml

1K Formats Covered

290–310 ml, foil packs 300/400/600 ml

Ratios Supported

1:1, 2:1, 4:1, 10:1

Key Takeaway: Choose MEDMIX for its MIXPAC standardisation, chassis rigidity, and ergonomics, ideal for long beads and viscous products.

 

Selection Guide: Drive Modes

 

Criterion

Manual

Pneumatic

Battery-Operated

Rate / Long Beads

Medium

High

High

High Viscosities

Medium

Very High

High

Precision

Very High

Medium

High

Operator Fatigue

Medium

Low

Low

Site Mobility

Medium

Limited

Very High

Key Takeaway:

  • Manual = Finesse and control.
  • Pneumatic = Speed and reduced effort.
  • Battery-Operated = Mobility and constant flow.

 

Selection Guide

 

The right dispenser gun is the one that stabilises your process and bead quality:

  • Product Viscosity/Rheology: (Fluid, paste, thixotropic) → Required thrust/pressure and targeted flow rate (ml/min).
  • Speed & Bead Length: Drive mode and battery/air capacity.
  • Format & Ratio: (50–600 ml, 1:1/2:1/4:1/10:1) → Body, piston, and static mixer compatibility.
  • Nozzle & Finish: Angled/“V”/straight, long tip, orifice diameter = desired bead width.
  • Environment/HSE: Temperature, noise, ergonomics, consumable waste management.

 

Accessories & Static Mixers

 

MIXPAC/Medmix mixers guarantee homogenous mixing right to the end of the cartridge. The length/diameter pairing drives back-pressure and mixing quality. Nozzles (angled, straight, “V”) and precision tips improve finish whilst limiting rework.

To guarantee service continuity, plan a stock of mixers, nozzles, pistons, seals, and adapters.

ACROM also offers compatible tool cleaners and smoothing agents, as well as maintenance packs by equipment family.

 

Best Application Practices

 

Standardised gestures remain decisive: initial purge (2K), verification of ratio and mixer change at each resumption, constant nozzle angle, and regular speed. A dispensing log (batch, nozzle, mixer, pressure/flow) facilitates quality audits.

Integrate the HSE dimension: effort reduction (pneumatic/battery), limitation of aerosols and splashes, ventilation and PPE according to SDS.

For certain zones, consider ATEX compatible equipment.

 

FAQ

 

Are the dispenser guns suitable for 310 ml silicone cartridges?

Yes: several 1K models accept 290–310 ml silicone and MS polymer sealant cartridges.

Can very viscous 2K structural adhesives (Epoxy, PU, MMA) be extruded?

Yes, with adapted pneumatic or battery-operated dispenser guns and a wide-diameter mixer.

Can one gun accept 310 ml and 600 ml?

Not without an adapter. Use a dedicated Combi dispenser or sausage gun for 400/600 ml formats.

How to choose my 2K static mixer?

According to ratio, viscosity, and targeted flow rate; length/diameter conditions back-pressure and homogeneity.

Manual, Pneumatic, or Battery?

Manual = Precision and short runs; Pneumatic = Speed; Battery = Mobility + Consistency without compressed air.

Which brand do you distribute?

ACROM exclusively offers MEDMIX solutions, with product compatibility advice and material testing.

 

About ACROM & Contact

 

ACROM supports your teams from equipment choice to production ramp-up: application station dimensioning, validation on your glues/sealants, operator training, stock of consumables and wear parts.

Contact our teams for a material test and configuration of your dispensing station.